EDGE MapFields

New device: EDGE 1050 !

Edge Mapfields is meant for use with the mapscreen on your device.
There are 4 fields, which every field can set with many options (see below).
It's created for Edge 1030, 1040, 1050, 530 and 830, 540, 840 and Explore and Explore2

This datafield is free of charge, but if you like it and use it, it would be nice to be invited to a beer: paypal.me/AndreasWirth

After installing the datafield on your device, place a full-width field under the map. In this field you put the EdgeMapsFields.

In the setup you can choose a display for each quadrant from many different options:
see:
https://apps.garmin.com/apps/30fdcbb5-a0f2-4832-9157-b7dcd81e7a0f

Both metric and statute format!

Time to Destination is calculated by your average speed. In the beginning - when no average speed is available - Time to Dest. is calculated by 10 km/h ( 6.214 mi/h).

Timer format is mm:ss for time less than one hour, and h:mm for time more than one hour.

Of course you can use this datafield on every screen with a datafield of 1/5 of the screen height.

Note: the pictures below are photoshoped to show all options on one picture.
You can only set one datafield on your device!

Top Replies

All Replies

mcinner1 10 months ago in reply to Marco

I've looked at my code and realized - it's not to much work to enable the datafield for half width for devices 1030 & 1040 series.

So, I ask: is that what you wanted?

Marco 10 months ago in reply to mcinner1

That would be epic ! That's exactly what I was looking for.
I just had a very simple version of that (as seen in simulator screenshot below), with top: speed, cadence and bottom: 3s power and HR.
Was planning on making a 2nd version with distance, time, gradient and altitude.
I like you layout just a lot better, and would love it if you could publish it. Would be nice to be able to have different values in both left and right datafield though :)

mcinner1 10 months ago in reply to Marco

The version is on the store!

Please check if all is ok and then I will release a clone.

(A nice review on the store would be great!)

bobbrisbane 10 months ago

I am loving your data field and am also using it in a 7B layout on my 1030. That way it takes up the bottom half of the screen. My problem is as follows. I have a varia Radar and really love the way your data field lets you know the approaching speed from behind. However, there appears to be a bug getting it to work every time. If it works when you start off, all is good, but usually it doesn’t. But by pausing the ride, then turning the Garmin off and on again, and resuming the ride, it works.

mcinner1 10 months ago in reply to bobbrisbane

Do you mean that radar speed show does not work consistently?

bobbrisbane 10 months ago in reply to mcinner1

It works every second time that I boot up my Garmin edge 1030.

mcinner1 10 months ago in reply to bobbrisbane

I use this datafield and never experienced that behaviour, nor have I ever heard from other users.
It seems to be a problem with the connection of your Varia and your Edge.

Check if there is a little orange dot at the crossing lines (see picture). This dot shows, that your Edge has recognised the Varia. No spot means no connection.

Just one hint: although I use radar only with my Varia, I let it connect as radar and light network.

bobbrisbane 10 months ago in reply to mcinner1

The Varia works fine. Yes with the dots and works perfectly with “My Bike Radar” data field.

dpawlyk 10 months ago in reply to mcinner1

mcinner1 said:
Just one hint: although I use radar only with my Varia, I let it connect as radar and light network.

It should work with just the radar connected. This isn’t likely to be the source of the problem. As far as ANT+ knows, the Varia is two devices.

6500654 10 months ago in reply to dpawlyk

This data field was perfect - used it in half width field for a while in 530 - but after recent release it stopped working - asking for full width - any option to return back possibility like was before?