This discussion has been locked.

You can no longer post new replies to this discussion. If you have a question you can start a new discussion

New 4.10 Software

HungryKid over 6 years ago

Any improvements with this new update? still waiting for mine to show up on Garmim Express.

Top Replies

Garmin-Matthew over 6 years ago +2 verified

Phased Rollout is at 100% as of 8/07/19 6:30 pm CST
ic3cold over 6 years ago in reply to Vaclav_Vodicka +3

I had a similar issue and contacted Garmin support. Problem was I wasn’t putting the light into pairing mode, I was just turning it on. So then edge only picked up the radar part. You need to do…
Martin Borsje over 6 years ago +1

Why no direct download link available, as for the beta's, for the interested visitors of this forum, instead of waiting till Garmin Express decides to upgrade?

All Replies

0 macko68 over 6 years ago in reply to micmac24

Grade was perfect for me on 3.50. Even on betas I had only few strange readings. On 4.10 however grade is all over the place. Often totally not corresponding with reality (ascent and -x% showing). Will reset the device but this is not good

0 Tim_B_ over 6 years ago in reply to Former Member

Interesting, I’ll give that a try next time. I’m going from memory of upgrading my 510, but thought re-pairing BT after an update was always a necessary step.

Thanks

0 Pdlpsher over 6 years ago in reply to micmac24

Updated to 4.10. Turned on the 830 and it can't find the phone unless I manually open up GC app. on the phone. I never have this problem on the 520. Very frustrating.

0 bglover11 over 6 years ago

Upgraded from the latest Beta to fw 4.10 this morning - first ride in a long time with no sensor dropouts so that's promising though time will tell. The one thing missing however with the new FW is noticed during a cycling workout.. the countdown beeps still work but the little start/finish triple chime noise is gone that signals the beginning/end of a segment of the workout. I do appreciate however that the ride no longer pauses/stops when the workout is complete!

0 herbbern over 6 years ago

Hello,

Edge 830 ( 4.10)

complete connection lost after 2 h . He doesn’t find the phone and sensors after a short coffee break. Manual search without success . The connection was restored immediately after Tour Save and reboot of the unit .

Connection: I-phone 8 (BT), Powermeter FC9100P (Ant+), Heart Rate Garmin (Ant+)

The same configuration worked flawless before with the last Beta Software.

Regards

0 ADLERSBERG over 6 years ago in reply to herbbern

same here, after 1:26 min dropped all sensors and never came back, after hard reset got back sensors.

0 Le_paulo over 6 years ago in reply to Former Member

Just tried that after upgrading - didn't work for me. The Garmin only paired correctly after loading GC app. I've only seen bluetooth pairing work properly on my iPhone 8 on a very early firmware release. None of the betas were better for me.

Easy enough to fix by loading GC app so not what I would call a critical fault.

0 micmac24 over 6 years ago in reply to micmac24

The issue with BT connectivity has certainly not been fixed yet; although the unit connects with the phone at the beginning it drops the connection during the ride for unknown reason and won't reconnect by itself. Rebooting HW does nothing.

0 DuaneHebert over 6 years ago in reply to Pdlpsher

It hasn't fixed BT for me. At least I don't seem to be able to upload the ride until I get close to WIFI.

0 jlinnemann over 6 years ago in reply to micmac24

I noticed the same problem during a ride in Belgium (using 4.10). The grade indicator at times indicated negative values (descent) while I was clearly climbing at 5%+. Over the 110K ride, the 830 reported total ascent of 1.359 meters. Strava corrected this to 2.293 meters, a huge difference.