This discussion has been locked.

You can no longer post new replies to this discussion. If you have a question you can start a new discussion

Only One Connect-IQ-Field usable in FW 5.00

I user dr6c1 and Stryp Zones as Connect-IQ-Fields fpr running.

After the update to Beta 4.87 i noticed that all Connect-IQ-Fields had changed to timer. Update to 5.00, all Connect-IQ fields have become timers again. Unfortunately, the same bug still seems to be there.
I was able to add dr6c1 to the activity again after a factory reset of the running activity and it is also displayed correctly, but when I add “Stryd Zones” or “Run Power” it is always only displayed as a timer. So far I haven’t found a solution to reactivate the “Stryd Zones”. Has anyone found a solution?

I found out something more:
If I remove my Connect-IQ field with dr6c1 I can easily add the "Stryd-Power" field and it will display correctly. Then, however, only the timer is displayed when adding dr6c1.

Apparently only ONE Connect-IQ field can be used since firmware beta 4.87. If you try to add a second one, it will be shown as a timer.

Top Replies

All Replies

0 4931875 over 4 years ago

I have now managed to fill both Connect-IQ fields again without the timer appearing.

The following procedure worked for me with dr6c1 and stryd:

Add the stryd field (will display correctly)
Add the dr6c1 field (will appear as a timer)
Now go to the first (stryd) correctly displayed Connect-IQ field and change the content to the other (dr6c1). Then go to the timer field and change the content to the stryd.
Everything is displayed correctly.

0 Former Member over 4 years ago

4931875

hi,

the ciq part

suggest you post this in the Garmin CIQ forum part
guess a resources problem between these two datafields
(used to have this ciq conflict on a FR935 between datafields from stryd and runscribe)
(and others also ... forerunner-945 - error-when-adding-2-connect-iq-df-in-the-run-app)

the datafields part

care to tell how you use these two datafileds for training
is one of them not enough ?

happy & safe sporting

0 4931875 over 4 years ago in reply to Former Member

hi,

guess a resources problem between these two datafields

I don't think so, because then I shouldn't make it work in any way

is one of them not enough ?

two of them are not enough ;-)

0 Former Member over 4 years ago in reply to 4931875

hi,

4931875 said:
I don't think so, because then I shouldn't make it work in any way

I do, that's why you should ask in the CIQ forum
one of the datafields grabs all the resources, while the other one only takes what is necessary
contact also the the devolopers of the datafields and let them know about the behavior

4931875 said:
two of them are not enough ;-)

so, you are new to running with power
it is what you prefer

happy & safe sporting

0 DrumPhil over 4 years ago

Yes i have the same issue on 5.00 - can only setup one CIQ field

0 6602582 over 4 years ago in reply to 4931875

worked, thank you :)

0 who knows over 4 years ago in reply to 4931875

4931875 said:
The following procedure worked for me

This worked for me also. Thanks for providing us a solution.

0 Former Member over 4 years ago in reply to who knows

DrumPhil , 6602582 , who knows

hi,

care to tell which datafield combinations do not work ?

or does it fail with any combination ?

(when not already done, calling : Brandon.ConnectIQ , Travis.ConnectIQ)

update:

also being mentioned now in the 5.0 thread ... forerunner-945 - phased-rollout-20---forerunner-945-sw-5-00

happy & safe sporting

0 who knows over 4 years ago in reply to Former Member

I was only trying to use the two data fields I have downloaded. Stryd and Steps to Fit.

0 6602582 over 4 years ago in reply to Former Member

Former Member

Stryd with RunPower or any Datarun (Ultimate/Premium) didn't work "as usual".

But with the workaround posted by @4931875 it seems to be ok know (no more timer fields)