Smart Bike Lights (Data Field) / Bike Lights Control (Widget)

No network means that your lights are not paired with your Garmin device. I don't have Cycliq lights so I don't know how well they support ANT+, try this link to pair the lights: https://cycliq.com/support/ce601/how-to-guides/ce-to-antconnection-guide-for-fly6-ce/ 

Hi,, I have verified that I am paired ( removed both and repaired for any case) 

My garmin device is fenix 6spro , i can chose a mode from there and it works.

I wanted to pull the numbers to use with data field , but the widget either says no network, or error 1 or IQ with exclamation mark.

That is really strange. Can you please try to pair only one light at a time to see whether the widget works with one light paired. So for every light try to do the following:
1. Remove all paired lights
2. Pair only one light
3. Check whether the widget still shows "No network"

yes, tried again removing both and re-adding only one... the widget sometimes does detect one light ( paired one ) but opening it get again iq logo with exclamation mark and no menu. , the lights are available and light mode changeable in the garmin menu ... which is a nightmare to get into on fenix.... , tbh i was hoping to pull numbers to use with the automatic data screen ... I can tell you what garmin light modes say... but there are no numbers... 

Thanks for trying it out. Unfortunately the reported crash from your fenix 6S Pro does not tell exactly where the problem is, so in order to find the root of the issue, I will create a test widget that will print the light information in a log file. From these information I will be able to see what are the differences between Cycliq and Garmin/Bontrager lights and hopefully find a solution to fix the issue. I will let you know when the test widget will be ready and I will provide the instruction how to use it in case you will be willing to test it out.

alexeinz said:

I can tell you what garmin light modes say... but there are no numbers... 

Yes, you can still tell me what light modes you see in the Garmin menu. This will help me out when I will get the required information from the test widget.

I've made the test widget, so in case you are willing to try it out, follow the following instruction: https://github.com/maca88/SmartBikeLights/tree/tester/Source/LightTester 
For fenix 6SPro the `LightTester.prg` can be downloaded here: https://github.com/maca88/SmartBikeLights/blob/tester/Source/LightTester/build/fenix6SPro/LightTester.prg 
On step 10 the content inside `LightTester.TXT` should be copied here.

This is how LightTester.TXT content looks like for my Bontrager ION Pro RT:

Net ST=2 MD=0 T=50693
T_L: 1
L0: TY=0 ID=1 LM=0 CM=[0, 1, 2, 5, 63, 62] BS=3
UPD: TY=0 ID=1 LM=62 BS=3 T=55494
UPD: TY=0 ID=1 LM=63 BS=3 T=57494
UPD: TY=0 ID=1 LM=1 BS=3 T=59494
UPD: TY=0 ID=1 LM=2 BS=3 T=61494
UPD: TY=0 ID=1 LM=5 BS=3 T=63494
UPD: TY=0 ID=1 LM=62 BS=3 T=66494
UPD: TY=0 ID=1 LM=63 BS=3 T=68494
UPD: TY=0 ID=1 LM=0 BS=3 T=71494

Thank you so much , I will test it in the evening today when I am at home. And report back.

This setup does not work (error4) :( I need the Bontrager ION200RT to turn on automatically in "Day Flash" mode after enabling recording in Garmin Edge 830 and the Garmin Varia RTL510 only flashed when the vehicle is approaching. I cannot set it :(

Freezyear said:

This setup does not work (error4)

If you are referring to the configuration in this post, then that is because it was for Varia 515.

This configuration should work:
1,1|:1H]0#4587520,196641#1,1|:1:63:1D=1#0,73404416#2,2|CAR:1:7:1I]-1]0|:1:0:1D=1#7,6:Ion 200 RT|2,:-1,Off:0|1,High:1|1,Medium:2|1,Low:5|1,Day Flash:63|1,Night Flash:62#5,4:Varia 510|2,:-1,Off:0|1,Solid:4|1,Day Flash:7|1,Night Flash:6#B3122#2#2#0#0

it will turn the ION 200 RT to Day Flash went recording and the Varia light will be turned on to mode "Day Flash" only when a vehicle is approaching and the timer is recording. But don't forget to set the control mode to smart mode "S" for both lights.

FLY6 CE and Fly12 CE .. settings seem same for both, the only peculiar thing, is once started they only momentarily report to widget and after that it goes network not found , they are still controllable thru the garmin menu , but it seems garmin is re-establishing ant+ connection every time.

 below is the whole file on few connex reattempts.

Net ST=2 MD=0 T=154681889
T_L: 1
L0: TY=2 ID=1 LM=0 CM=[0, 1, 2, 3, 6, 7, 63, 62, 61, 60, 59, null] BS=3
Net ST=2 MD=0 T=154702427

T_L: 1
L0: TY=0 ID=1 LM=0 CM=[0, 1, 2, 3, 6, 7, 63, 62, 61, 60, 59, null] BS=4
Net ST=2 MD=0 T=155176821

available settings are:

constant high, medium, low

flash high, medium ,low

pulse high, medium, low

off

full log 

Net ST=2 MD=0 T=154681889
T_L: 1
L0: TY=2 ID=1 LM=0 CM=[0, 1, 2, 3, 6, 7, 63, 62, 61, 60, 59, null] BS=3
Net ST=2 MD=0 T=154702427
T_L: 1
L0: TY=7 ID=1 LM=0 CM=null BS=null
Net ST=2 MD=0 T=154837043
T_L: 2
L0: TY=7 ID=1 LM=0 CM=null BS=null
L1: TY=7 ID=2 LM=0 CM=null BS=null
Net ST=2 MD=0 T=154850183
T_L: 2
L0: TY=7 ID=1 LM=0 CM=null BS=null
L1: TY=7 ID=2 LM=0 CM=null BS=null
Net ST=2 MD=0 T=154860999
T_L: 2
L0: TY=7 ID=1 LM=0 CM=null BS=null
L1: TY=7 ID=2 LM=0 CM=null BS=null
Net ST=2 MD=0 T=154867358
T_L: 2
L0: TY=7 ID=1 LM=0 CM=null BS=null
L1: TY=7 ID=2 LM=0 CM=null BS=null
Net ST=2 MD=0 T=154983791
T_L: 1
L0: TY=2 ID=1 LM=0 CM=[0, 1, 2, 3, 6, 7, 63, 62, 61, 60, 59, null] BS=5
Net ST=2 MD=0 T=154989706
T_L: 1
L0: TY=2 ID=1 LM=0 CM=[0, 1, 2, 3, 6, 7, 63, 62, 61, 60, 59, null] BS=5
Net ST=2 MD=0 T=154992765
T_L: 1
L0: TY=7 ID=1 LM=0 CM=null BS=null
Net ST=2 MD=0 T=154995793
T_L: 1
L0: TY=7 ID=1 LM=0 CM=null BS=null
Net ST=2 MD=0 T=154998979
T_L: 1
L0: TY=7 ID=1 LM=0 CM=null BS=null
Net ST=2 MD=0 T=155009808
T_L: 1
L0: TY=7 ID=1 LM=0 CM=null BS=null
Net ST=0 MD=null T=155069305
Net ST=0 MD=null T=155084148
Net ST=0 MD=null T=155089715
Net ST=2 MD=0 T=155113353
T_L: 1
L0: TY=0 ID=1 LM=0 CM=[0, 1, 2, 3, 6, 7, 63, 62, 61, 60, 59, null] BS=4
Net ST=2 MD=0 T=155176821
T_L: 1
L0: TY=7 ID=1 LM=0 CM=null BS=null