Related
This discussion has been locked.
You can no longer post new replies to this discussion. If you have a question you can start a new discussion

New Edge 1030/1030 Bontrager Public Beta 12.14 Now Available

Garmin-Matthew
over 3 years ago

A new Beta software for the Edge 1030 has been released. Full change log, instructions, and software for installing the beta can be found in the link below.

Edge 1030 (12.14): https://www8.garmin.com/support/agree.jsp?id=12819 

Edge 1030 Bontrager (12.14) : https://www8.garmin.com/support/agree.jsp?id=15716 

  • For any issues that you encounter please fill out the form included in the download and attach it to an email to [email protected]. Please note that you may not get a response to the email unless we need more information on the issue you report.
  • Although this software is believed to be reliable, it has not yet been released for production and should be used at your own risk.

Changes made from version 12.00 to 12.14:

  • Fix issue with Fazua BLE scanning
  • Fix crashes drawing third party maps
  • Fix issue unlocking maps from SD card

Installation Instructions

  1. Connect your Edge 1030 device to your computer using the micro-USB cable.
  2. Download and unzip Edge1030_1214Beta.zip and place the GUPDATE.gcd file in the \Garmin folder of your device's internal storage drive.
  3. Disconnect your device from the computer, approve the update on the Edge, and wait for the update to finish.
  4. If you would like to revert to the last public release software, follow the above steps but place the GUPDATE_1200.GCD file in the \Garmin folder. Rename the file to GUPDATE.GCD before disconnecting your device.
    NOTE: If you revert to an older version of software, all of your settings will be reset to defaults.
  • 0 over 3 years ago in reply to krazyeone

    I thought the image I posted was similar to your issue, The response shown in the image is caused when panning the map whilst also navigating. Looks like I was mistaken making the comparison. . As you experiencing the blank portion of the image actually flickers too but not always

    . 

  • 0 over 3 years ago

    just upgraded from 12 to 12.14, no issues jet but in general the device becomes slower and slower to startup as well as when you zoom in during a ride on the map it cannot refresh. Are we now with all the new features we got over last years not at the end of the HW limitation and should we better go for the new 1030 Plus or does this device have the same slow bootup and zoom on the map. For the rest I am still pleased with my Edge 1030 Slight smile

    Stefan

  • 0 over 3 years ago in reply to saaal74

    I have this problem too.  It seems to be many sensors for me as the same issue occurs with my Garmin lights/radar and my HR strap.  The speed and cadence sensors seem to be OK but everything else regularly disconnects for a couple of seconds and then reconnects for a random amount of time.  Sometimes it becomes stable for a few minutes and at other times it loops through connects and disconnects every few seconds.  I've only seen this issue since upgrading to the 12.13 snd 12.14 betas, it wasn't happening at 12.0.

  • 0 over 3 years ago

    I had the same problems with sensors disconnect , more than this , I had an issue with HR and I kept the sensor in the back of my pocket , and I had connect disconnect over and over again

  • 0 over 3 years ago in reply to krazyeone

    I am quite sure the sensor goes to sleep if it does not detect a hearth beat. So in your pocket the connection could not be reliable. It needs to be on your skin with good electrode contact to wake-up and transmit.

  • 0 over 3 years ago in reply to Martin868

    agree with you, but , for some reason, it was connecting and disconnecting, as it was not connected at all to the strap