Related
This discussion has been locked.
You can no longer post new replies to this discussion. If you have a question you can start a new discussion

Forerunner 945 Beta SW 3.08 is now available!

Garmin-Blake
over 5 years ago

Download here. 

Notes:

  • For any issues that you encounter please fill out the form included in the download and attach it to an email to [email protected]. Please note that you may not get a response to the email unless we need more information on the issue you report.
  • Although this software is believed to be reliable, it has not yet been released for production and should be used at your own risk.

Change History

Changes made from version 2.80 to 3.08:

  • Added PacePro feature.
  • Added additional data field configurations (5 and 6 field).
  • Added graphical gauge data fields (i.e. Heart Rate, Cadence, etc.)
  • Improve ANT+ and BLE sensor management
  • Bluetooth software update to address battery life issues that could occur on some devices
  • Improvements to headphone pairing and media player
  • Improvements to golf
  • Improvement/fixes for Connect IQ
  • Some improvements for segments/Strava segments
  • Various other fixes/improvements

Installation Instructions

  1. Connect your Forerunner 945 to your computer using the USB cable.
  2. Download and unzip Forerunner945_308Beta.zip. Place the GUPDATE.GCD file in the \GARMIN folder of your device's internal storage drive.
  3. In Forerunner945_308Beta, go to the RemoteSW folder. Place the GUP3114.GCD and GUP3303.GCD file in the \GARMIN\REMOTESW folder of your device's internal storage drive.
  4. Disconnect your device from the computer, approve the update on the watch, and wait for the update to finish.
  5. If you would like to revert to the last public release software, place the GUPDATE-280.GCD file in the \GARMIN folder. Rename GUPDATE-280.GCD to GUPDATE.GCD before disconnecting your device. To revert the RemoteSW, place the RemoteSW\Downgrades\GUP3114-250.GCD and RemoteSW\Downgrades\GUP-3303-360.GCD in the \GARMIN\REMOTESW folder. NOTE: If you revert to an older version of software, all of your settings will be reset to defaults.
  • 0 over 5 years ago

    Do we know when the stable update will be available?

  • 0 over 5 years ago in reply to Kub3k

    When the bugs are ironed out of the beta ?! 

  • 0 over 5 years ago in reply to kaineken

    If you are at a heart rate below your lowest HR Zone, it will show all the way to the left and outside of the gauge. 

  • 0 over 5 years ago

    It reappered a bug that was solved in previous firmware: with backlight set to 8 seconds, when starting a run activity the backlight stay on till when the watch finds a gps fix

  • 0 over 5 years ago in reply to JeremyBlck

    I experience the exact same thing. The OHR is quite accurate when cycling IF I'm recording the activity. If not recording, the OHR is way off. Just had my Rev C replaced with a Rev D because of button issues, no change on the OHR problem. 

  • 0 over 5 years ago

    Enjoying the 6 fields screen (finally!!!).

    Yet, yesterday, while riding and using the watch its screen froze.

    No button was working to change this except from lond press on the power button to have it reset.

    Apparently it continued to record even when the screen was frozen, as I noticed it ~40min after it was stuck and got all the milage and climb I did completely.

    Except from the firmware update, no other update was done for the watch (watchfaces, widgets and so on).

  • 0 over 5 years ago

    yesterday i made a run with connected BLT headphones, finished run and pressed stop, then headphones disconnected and it looks like BLT on watch was dead, restarted watch, restarted mobile phone, no change, the pairing wasn't possible, after a hard reset of the watch the pairing went OK!

  • 0 over 5 years ago

    For me not works correctly. 

    Every day when I wake up can't connect with mobile phone 

  • +1 over 5 years ago

    @Garmin-Blake do you know if the OHR is still a thing in development for now?  I ask because for me (and some others in this forum) the OHR went south when you introduced the swimOHR.

    Also this beta-version (which offers some nice improvement like the 6-fields screen. thumbs up for that) does not solve this problem for me. I can no longer use the OHR at all. It's just plain wrong ALL time.  I gave it a try during a 6h trail-run again and it never showed any value which was even closely correct. (e.g. on >20% inclines it showed 120HR and on smooth and relaxed downhills I got values even higher than my maxHR).

    Before the OHRs of several Garmin-watches worked really good for me. The OHR of my Fenix 5+ still does, so I know how to wear a watch with OHR. I'm doing it for years and it worked for several years pretty good. But with the current 945 it's just garbage.

  • 0 over 5 years ago

    Hi,

    someone else having problems with stryd recording? After update two days ago two recordings failed with empty power data.

    The Stryd is connected as Running Sensor via ANT.

    FW: 3.08

    GPS: 2.50

    WiFi 2.60

    CIQ: 3.1.4 

    WHR: 20.04.50

    ANT'/BTLE/BT: 4.19 

    Sensor HUB 2.55