This discussion has been locked.
You can no longer post new replies to this discussion. If you have a question you can start a new discussion

GPSMAP62S - waypoint - can't delete?? Software?

Former Member
Former Member
Hi,

I really am not sure which section to post this in.
I have a GPSMAP62S.
I updated the firmware to Ver2.40 using the Garmin Webupdater.
Unit works fine - even loaded and panned over my first custom maps.

The issue is deleting a waypoint in the Waypoint manager.
I downloaded the manual to make sure i was clear on Garmin's process.
When i hit menu - it shows ONLY "Delete All".
THere is no delete for just one waypoint.
I tried each of my 3 waypoints separately.
In the end i tried the "delete all" and yes it deleted all 3 at once.
I know the workaround, but i really would prefer a working quick delete.

Is this a software issue?
Or is there anything i can do?
Please advise
(1) If this is the right place to post this question
(2) and please advise a solution.

Thankyou.
  • Former Member
    0 Former Member over 14 years ago
    I found this SAME issue reported on another forum.
    So i know it's not just me.
    Again it was a 62S.
  • Former Member
    0 Former Member over 14 years ago
    Well a whole day has gone by without a reply.
    It's an easy thing for any Garmin tech to check - things that make a consumer go "hmmmm". Perhaps this is not what the forums are intended for?
  • This forum is not an official line of support. I would recommend contacting Garmin Support.
  • Former Member
    0 Former Member over 14 years ago
    Thank you for clarifying that.
    I did indeed send in a query to Garmin support as well.
  • Former Member
    0 Former Member over 14 years ago
    Issue is now sorted out.

    First it was suggested to do a master reset:
    I would recommend doing a master reset on your unit.

    **This will erase all user data. Please back up your information before
    doing the reset**

    With the unit off, press and hold these 3 buttons for 5 seconds.
    Enter + Page + Power
    You will see a screen that says “Do you really want to erase all user
    data?”
    Say yes
    If successful all user data will be erased.

    Then reload the data.
    excerpt of correction of procedure>>"you do NOT keep holding down the power button, but release the
    power as soon as the Garmin screen appears but you do keep holding the
    enter & page. "


    Then came the prompting that i was in the wrong place.
    I was in the main waypoint manager folder where you see all the waypoints.
    I thought highlighting one and hitting menu should bring up the delete option.
    Not so. Instead these are the directions:

    If you would like to delete a specific waypoint, then please go to Main
    Menu > Waypoint Manager > Select the Waypoint that you would like to
    delete > Press Enter. Once you are on the selected waypoint page, then
    please Menu. You will see an option to delete just this one waypoint.

    So the difference is you are WITHIN the attributes page and then you hit menu. I write this in case someone else comes from a software organizational perspective (OOP) like me.
  • Former Member
    0 Former Member over 14 years ago
    To delete waypoints from the device please follows the steps below.

    1. Power the device on and hit the menu button twice to reach the main menu.
    2. Scroll down and hit enter on “Waypoint Mgr.”
    3. Select the waypoint you wish to delete and hit enter on it.

    From this point you can hit the menu button once and get a list of option you can do with the device. The top option will be to delete the waypoint. This will not delete all the waypoints.


    Hope this helps.
  • Former Member
    0 Former Member over 14 years ago
    Instead of clicking menu on a highlighted waypoint, click enter. You will get that waypoints specific page. Now click menu and you should get various options includung a delete option for that specific waypoint.