Montana 710i/ 760i - Recent Threads

How to enable bluetooth on 760. I can't connect via garmin connect only garmin explore.

8107965 — Fri, 08 May 2026 11:06:48 GMT

I factory reset my phone now Garmin Connect says enable blue tooth on the 760. It works through Explore but not Connect. Bluetooth is already working. I've uninstalled and reinstalled.

760i is not showing private land while inside a national forest.

scott — Tue, 28 Apr 2026 00:54:47 GMT

My 750i always showed. I didn't have any special maps with 750i. I have topactive maps loaded but can't tell if it is "on". Would wide dem baseman is "0n. I also have 3 topo usa mapsets loaded and on. I have to be missing something basic. Doesn't seem to be the zoom level. Do I need a special mapset? My maps are the the older 100k version. Any information will be helpful

Montana 760i stuck in boot loop

james.grzech — Fri, 27 Feb 2026 18:06:50 GMT

760i stuck in boot loop. soft reboot fails, hard reset fails. Germin Express fix fails. Removing battery for over an hour fails. No SD card in device. Suggestions?

Montana 760i shuts off or freezes everytime I use Outdoormaps+, any Firmware Updates at the Horizon?

ahoibrowse — Thu, 05 Feb 2026 20:37:10 GMT

I paid lots of money for the Montana 760i, paid again for OutdoorMaps+ only to watch the device shut off or freeze when using the map screen. This device has one Job: be reliable on matter what. Orherwise I simple use my phone and Save the money.

is there any Firmware Update at the horizon?

Accessing custom maps from 710i

4141712 — Sat, 13 Dec 2025 01:11:14 GMT

I've just bought the Montana 710i and am trying to access a custom map. I've saved the .kmz file to the device (both using internal storage and a microSD card - following the recommended file paths Garmin/CustomMaps/). The files are listed under the device and open in BaseCamp when connected to the PC, but I can't find any option for Custom Maps in Map Manager on the device itself to access or open the map.

"Montana is busy...."

MatthewCarmody — Sun, 07 Dec 2025 00:11:09 GMT

Anyone struck this while trying to sync wirelessly? Tried to sync while I had mobile data coverage last week (BT or Mobile hotspot) and each time the messages was that the Montana 710i was busy and to try again later.

Deleted the pairing, re-established the pairing and still no better. Both devices were at idle and both have UTD software.

Suggestions?

No off course alerts, silent change a course prompts

1796894 — Thu, 13 Nov 2025 11:52:39 GMT

Hello, i found a problem - there is no off course alerts. If you change settings for change a course with monit, there is silent prompt with ask to change it. Software version 23.40

Custom POI Proximity Alarms on Montana 710

MartinB14 — Wed, 01 Oct 2025 13:47:46 GMT

I have used POI Loader to install over 200 Custom POIs onto my device. The POI Loader software gives the option to set a proximity for all Custom POIs, but doesn't seem to load these as Proximity Alarms to the device.

I want to set the same Proximity Alarm for all 200+ Custom POIs. Is there a way of doing this in bulk - ie select multiple POIs (or other waypoints) and set the same Proximity Alarm for them all? I can set them one at a time, but that's going to be pretty tedious for over 200 points, so am looking for a way to apply the same alarm to multiple waypoints/POIs.

Loading KMZ files onto 760i

6904208 — Fri, 22 Aug 2025 23:58:41 GMT

I have KMZ map files loaded onto a microSD inserted into my 760i. What next? How do I access the maps? Note that I cannot load maps from my computer because it is a Mac running the latest OS and it refuses to acknowledge that my Garmin exists as a drive when connected by cable, despite Garmin Express being able to update software etc etc. (I have followed all the instructions in the manual about connecting to the computer, and followed all the troubleshooting tips.)

How can I reconcile routing method between Basecamp Routing and Garmin 760I routing method?

d2reid — Sat, 14 Jun 2025 13:41:13 GMT

I have been using Basecamp for years. So I bought a new Montana 760i to help me navigate on my new motorcycle. I create a route in basecamp, select activity as motorcycle, then select +more at the bottom of the route edit page and select "Curvy Roads". But when I load the route into my 760i and select Motorcycle Activity it asks for Direct, Time, Distance preference. Then it recalculates the route to something that is no where near what I so painstakingly plotted out in Basecamp.

I have been unable to find "Curvy Roads" option inside the Montana 760i as a route option. I am investigating "New Profile" to see if I can get the thing set up to optimize the routing method for motorcycle riding.

Any suggestions, ideas, help, etc. would be appreciated.

Montana 710i/ 760i

Garmin - LF — Fri, 16 May 2025 20:23:29 GMT

Now available: Forum support for the Montana 710i/ 760i

For more information:

https://www.garmin.com/en-US/p/1436101/pn/010-02964-10/

https://www.garmin.com/en-US/p/1436461/pn/010-02964-00/

Map Manager Queue Problem - queued updates on 760i

6815277 — Sat, 19 Apr 2025 15:52:31 GMT

Hello, I am a new Montana 760i user in Türkiye. I bought the Topoactive Europe map. Despite many attempts, I could not load the map onto the device. Each time, Map Manager says "queued" and waits. After a while, it starts downloading again by itself. Despite several attempts, I could not overcome this situation. I have seen people experiencing this very annoying situation on different Garmin devices here. But I could not see anyone experiencing the same problem with the Montana 760i. So please help me. Thank you in advance.